• News
  • Competitions
  • Recipes
  • Beauty
  • Fashion
  • Gifts
  • Rest
The main


New materials in the section
  • Birch mushrooms: recipes of preparation of mushroom dishes
  • We buy the built-in refrigerator
  • Photowall-paper: choose intelligently
  • How to weld paste from a flour?
  • Drawing room and bedroom in one room (photo)
  • We consider square meters in the correct and wrong form
  • Installation of a balcony: documents, works





New materials
  • Royal delicacy: gentle boiled pork in house conditions
  • You will lick fingers: tasty chicken thighs
  • It is useful and quickly: the most tasty recipes of tvorozhnik
  • The most delicate charm: recipes of tasty chocolate glaze for a pie
  • The main guest on a table: the best recipes of home-made bread on ferment
  • Unusual seasoning: marinated capers and recipes on their basis
  • Our food: the best recipes of Russian cabbage soup from sauerkraut
  • How to prepare a sturgeon and a sterlet in an oven entirely: recipes of original dishes with a photo
  • The best toasts on birthday in verses and prose
  • The most cheerful and cool toasts in verses and prose
The main > Repair> Venetian plaster the hands

Venetian plaster the hands

  • 1
  • 2
  • 3
  • 4
  • 5
49

Венецианская штукатурка своими руками The finishing of walls fashionable presently called by "the Venetian plaster" came to us from Ancient Rome. Mixes for the Venetian plaster consist of dust of various grades of a stone, for example, of marble, binding substance, for example, of acryle, and dyes. Technology of putting the Venetian plaster the special. Process this laborious and labor-consuming, and therefore such finishing costs much. But it is possible to execute finishing of walls on the "Venetian plaster" technology and by own efforts. The main thing – attention and patience!

For you for finishing performance "the Venetian plaster" such tools and materials will be necessary:

  • mix for the Venetian plaster
  • color
  • trowel (it trowel)
  • damp rag
  • mitten suede
  • wax

Technology of putting the Venetian plaster

Before beginning finishing with the Venetian plaster, it is necessary to prepare a surface of walls. Walls have to be ideally equal, pure and dry. Under the Venetian plaster often put the special primer intended for the best coupling of plaster with a surface.

Prepare plaster solution for what mix plaster and a color. Do not knead at once too much solution not to allow its premature hardening and drying.

Apply a small amount of solution on a trowel. Lean the tool against the processed surface at an angle approximately in 30 ° and, strongly pressing it, carry out on a surface. At once after the first dab carry out a trowel the second dab, perpendicular to the first.

The plaster coat has to be very thin, approximately equal on thickness of 0,1 mm, and equal. Wipe a trowel a damp rag more often that on it the dried-up solution particles which can scratch a plaster surface were not formed. Leave a layer for drying for 6-12 hours. If after drying of plaster on a surface of a wall there were acting roughnesses, they can be removed with the little pallet accurately.

After drying of the first layer can start drawing the second. To gain "marble" effect, make the second layer is lighter or is more dark than the previous. After drying again accurately remove roughnesses. Repeat the same and for the following layer. In total it is required to put from three to ten very thin plaster coats. Every time let's a layer time dry out.

After you put the last layer, within 15 minutes let's it dry up and start the following stage of works – polishing. To execute polishing, take a trowel and, driving it practically closely into the corner, carry out it on a covering surface. Move a trowel in various directions.

It is possible to pass to a stage of waxing not earlier than in a week after the end of polishing. During this time plaster properly will dry. Wax can be applied by means of a trowel. Do dabs by wax multidirectional. It is necessary to apply wax with a thin layer, differently in places where wax is applied especially densely, after drying there will be dark stains.

After drying of a wax covering polish a covering surface with a suede mitten. Roundabouts, densely pressing a mitten to a covering, process all surface of a wall.

Well, here! It is a little efforts and at you the Venetian plaster is ready. We congratulate!

Council. If you are not sure of the forces, before finishing of a wall, test technology of putting the Venetian plaster on a leaf of a cardboard.

Read also on our site:

How to build the country houseКак построить дачный дом The house the hands — is an excellent way to save both on building materials, and on a salary of builders. In this case builder quarrystone...
to read further

Automatic doorsАвтоматические двериAll know how automatic doors are convenient, especially when hands are occupied with packages or bags at an exit from a supermarket. The drive of an oar door on the design of N...
to read further

How to choose a metal doorКак выбрать металлическую дверьChoosing an entrance door, we first of all pay attention not to appearance of a door, and to its reliability and safety. Already passed those times, to...
to read further

<What to do if... Useful tips on repairGypsum cardboard the hands>

The mainAbout the project
© InfoHow.net
The site does not bear responsibility for any information published on the website. All materials are presented for acquaintance. The decision on application of councils by users is carried out independently under the responsibility.